S54-30 Polyurethane Oil-proof Surface Paint

S54-30 Polyurethane Oil-proof Surface Paint (double components)

Intended Uses Paint film is resistant to crude oil, 95/130 aviation gasoline, avlation kerosene, 40# engine oil, 120# gasoline, kerosene, diesel and various other oil products and has no impact on oil quality (gelatine≤7mg/100mg) with excellent corrosion-proof and physical mechanical properties. It is applied to inner wall of oil bath, oil cabin and oil tank as surface paint.
Product Description It is prepared by hydroxylated resin, polyisocyanic acid prepolymer, pigment and filler, auxiliaries and solvent, etc. It si packed into Component A and Component B.(Various Colors)
Product Information Volume Solids 30%
Dry Film Thickness 25 microns
Theoretical Coverage 100g/m2,12.90m2/L(calculated by 35μm dry film)
Application Details Mix Ratio Component A (paint): Component B (curing paint)=3:1(weight ratio)
Curing Time 23±1℃
Method of Application  
Airless Spray Recommended-Tip range 0.33-0.41mm, Output fluid pressure; 17.6-21.1MPa(176-211Kg/sq.cn)
Brush or Roller Recommended, only for small area.
Conventional Spray Adoptable but thin to 5-10%, Tip range:2-2.5mm
Thinner X-10
Cleaner X-10
Pot Life 25℃;1 hour
Storage Life One year
Full Solidification
Overcoating Interval
Minimum Maximum
0℃       3 hours 2 days
25℃ 2 24 7 2 hours 1 day
35℃       1 hour 16 hours
Painting number Suggest spraying or brushing 2~3coats, dry film reaches 70~100μm.
Storage and Handing Storage Store in cool and dry conditions
Pack Size Component A 21kg, Component B 7kg
Flash Point Component A 25℃, Component B 30℃
Specific Gravity Apprpx 1.29kg/L
Specification and Surface Preparation Paint polyurethane oil-proof surface paint within stipulated painting interval of preceding coat.
Preceding Paint Plyurethane iron red primer.
Limitations Double-componet paint must be fully stirred and preciously mixed according to stipulated quality and construct it after resting for 10 minutes. Substrate temperature must be 3℃higher than that of dew point and relative humidity must be lower than 85%.
Safety Precautions This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.
This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done;
The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air.
Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary.
Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately.
Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation. Handle empty containers with care and do not bring about environmental contamination.
NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.