%{tishi_zhanwei}%

HS61-160 Epoxy Polyurethane Heat Resistant Anticorrosive Paint

HS61-160 Epoxy Polyurethane Heat Resistant Anticorrosive Paint (primer/surface Paint, Double/triple Components)

Intended Uses Paint film has excellent acid ,alkali, salt and chemical air corrosion resistance performances, oil, water and solvent resistance performances; coating is tough, with strong adhesion and good heat resistance. The color will slightly change after a long time use at 160℃ but not influence protective performance; it is applicable to steel or concrete cement chimney inner surface and other steel structures as well, relative humidity must be lower than 85% in 5~35℃.
Product Description  It is prepared byhydroxyl components containing epoxide resin, corrosion and temperature resistance pigment and filler. It is packed into Component A and Component B; Component A is lacquer of primer and surface paint; Component B is common curing agent of primer and surface paint. (Primer: iron red; surface paint: reddish brown, medium green, dark grey)
Product Information Volume Solids Primer: 60%,Surface paint: 55%
Dry Film Thickness Primer: 70 microns, Surface paint: 25 microns
Theoretical Coverage Primer: 140g/m2 (calculated by 40μm dry film)
Surface paint: 140g/m2 (calculated by 40μm dry film)
Application Details Mix Ratio Primer: Component A : Component B =3:1(weight ratio)
Surface paint: Component A : Component B =2.5:1(weight ratio)
Curing Time 23±2℃:20min
Method of Application  
Brush or Roller Recommended, only for small area.
Conventional Spray Adoptable but thin to 5-10%, Tip range: 2-2.5mm
Thinner HS Special diluent
Cleaner HS Special diluent
Pot Life 25℃:6~8 hours
Storage Life One year
Drying
Time
Substrate
Temperature
Touch
Dry
(h)
Hard
Dry
(h)
Full Solidification
(d)
Overcoating Interval
Minimum Maximum
25℃ ≤4 ≤24 7 8 hours 3 days
Painting number Suggest sparying two costs of primer and 2~3 coats of surface paint; dry film reaches 140~160μm
Storage and Handing Storage Store in cool and dry conditions
Pack Size Primer: Component A 21kg, Component B 7kg
Surface paint: Component A 20kg, Component B 8kg
Specific Gravity Primer: approx 1.55kg/L, Surface paint: approx 1.52kg/L
Specification and Surface Preparation  Steel surface requires sand blasting or shot blasting for derusting to Swedish Derusting Standard Sa2.5, or grinded to St3 by electric tools.
Limitations Relative humidity must be lower than 85% when temperature is 5~35℃.
Safety Precautions This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.
This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done;
The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air.
Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary.
Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately.
Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.
Handle empty containers with care and do not bring about environmental contamination.
NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.