BS52-12 Acrylic Polyurethane Surface Paint

BS52-12 Acrylic Polyurethane Surface Paint (two components)

Intended Uses	Paint film is smooth and bright, with luxury decoration, excellent weather resistance, salt spray resistance, chemical corrosive resistance and outstanding washability, good wet and hot resistance and weat resistance. It is applicable to outer decorative and protective painting of various machine body, also can be used on bridge, hull and industrial equipment as protective painting.
Product Description	It is prepared by pure acrylic resin containing hydroxyl group, aliphatic isocyanate curing agent, pigment with light resistance, various anxiliary and solvents. It is packed into Component A and Component B. (Various colors)
Product Information	Volume Solids		60%
	Dry Film Thickness		75 microns
	Theoretical Coverage		240g/m²(calculated by 75μm dry film)
	Practical Coverage		Allow appropriate loss
Application Details	Mix Ratio		A:B=8:1(By weight)
	Curing Time		23±2℃：20min
	Method of Application
	Brush or Roller		Recommended, only for small area.
	Conventional Spray		Adoptable but thin to 5-10%, Tip range:2-2.5mm
	Thinner		X-13
	Cleaner		X-13
	Pot Life		25℃：6 hours
	Storage Life		One year
	Drying Time	Substrate Temperature	Touch Dry （h）	Hard Dry （h）	Full Solidification （d）	Overcoating Interval
						Minimum	Maximum
		25℃	0.5	24	7	2 hours	7 hours
Storage and Handing	Storage		Store in cool and dry conditions
	Pack Size		Component A 20kg, Component B 2.5kg.
	Flash Point		27℃
	Specific Gravity		Approx 1.30kg/L
Specification and Surface Preparation	If preceding paint has been polluted, appropriate methods shall be used to remove grease and dust and this lacquer diliuent can be used to clean.
Preceding Paint	Polyurethane iron oxide red primer, epoxy zinc rich primer, epoxy micaceous iron oxide anti-rust paint and inorganic zinc rich primer.
Limitations	Substrate temperature must be 3℃ higher than dew point above, and relative humidity must be less than 85%.
Safety Precautions	This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product. This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done; The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air. Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary. Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation. Handle empty containers with care and do not bring about environmental contamination. NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.