%{tishi_zhanwei}%

H53-8 Epoxy Primer Of Red Lead

H53-8 Epoxy Primer Of Red Lead

Intended Uses As primer for many uses, designed to spray new-built structure or maintain steel structure. Easy application, high protective property. As Epoxy resin anti-corrosive primer, can be overcoated with extensive high build finish.
Product Description Two packages, Epoxy primer of red lead with good abrasion resistance and a little machenical damage.
Product Information Volume Solids 58%
Dry Film Thickness 40microns equivalent to 70 microns of wet film
Theoretical Coverage 150g/m2(calculated by 40μm dry film)
Pratical Coverage Allow appropriate loss
Application Details Mix Ratio A: B =100:6(By weight)
Method of Application
Airless Spray Recommended-Tip range 0.35-0.53mm (15-21thou), Output fluid pressure: no less than 17.6MPa(176Kg/sq.cm)
Brush or Roller Suitable for small area. Recoating should be conducted for many times in order to reach the required thickness.
Conventional Spray Suitable, diluted to 12%
Thinner Not necessary in normal, If needed, use X-7
Cleaner X-7
Pot Life 5℃:12h 23℃:8h 35℃:3h
Storage Life One year
Drying
Time
Substrate
Temperature
Touch
Dry
(h)
Hard
Dry
(h)
Overcoating Interval
Minimum Maximum
5℃
23℃
35℃
8
2
0.5
36
24
12

24 hours
16 hours
12 hours

14 days
Storage and Handing Storage Store in cool and dry conditions
Pack Size Component A: 25kg
Component B: 1.5kg
Flash Point Above 23℃(Basic agent, curing agent or their Mixture)
Specific Gravity Approx 2.30kg/L
Specification and Surface Preparation Remove grease by solvent cleaning. Remove weld slag, Smooth weld seams and sharp edges. The surface to be coated must be clean and dry.
Blasting: Blast clean to Swedish Standard SIS055900 Sa2.5, or clean to Pt3 (JSRA SPSS 1975) by power tool. Try to smooth, fill or properly treat the surface blemishes arisen from blasting.
Limitations This product can not cure below 5℃. The optimum curing effect is resulted above 10℃.
Safety Precautions This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.
This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done;
The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air.
Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary.
Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately.
Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.
Handle empty containers with care and do not bring about environmental contamination.
NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.