LF53-11 Fluorine Carbon Iron Oxide Red Anti-rust Paint

LF53-11 Fluorine Carbon Iron Oxide Red Anti-rust Paint (two components)

Intended Uses Print film has good physical and mechanical performance, excellent anti-rust, anti-corrosion, heat resistance and salt spray resistance performances. It is applicable to steel, aluminum, copper plate, stainless steel, galvanized plate surfaces, and it can be used as super weather resistance and anticorrosive primer on metal surface like crash barrier, railway bridge, transportation vehicle and chemical machinery equipment etc.
Product Description This paint uses high-grade fluorine carbon resin as basic material, compounding with anti-rust filler, auxiliaries and slovent, etc. (iron red and matt)
Product Information Volume Solids 45%
Dry Film Thickness 40 microns
Theoretical Coverage Allow appropriate loss
Application Details Mix Ratio Component A : Component B =10:1(weight ratio)
Curing Time 23±2℃:0.5-1h
Method of Application
Airless Spray Recommended-Tip range: 17-21mm; Total fluid pressure: 15-20 Mpa
Brush or Roller Recommended, only for small area.
Conventional Spray Adoptable but thin to 5-10%, Tip range:2-2.5mm
Thinner X-20
Cleaner X-20
Pot Life 5℃:12h 25℃:8h 35℃:6h
Storage Life One year
Full Solidification
Overcoating Interval
Minimum Maximum
25℃ 1 24 7 1 hours No limit
Storage and Handing Storage Store in cool and dry conditions
Pack Size Component A 20kg, Component B 2kg.
Flash Point 27℃
Specific Gravity Approx 1.33kg/L
Specification and Surface Preparation Steel surface reaches Swedish Derusting Standard Sa2.5 or Derusting to St3 by manual or electric tool after shot blasting or sand blasting, surface roughness shall be controlled within 40~80μm. Steel surface shall be painted with anti-rust paint within 24h after rust removal to avoid the secondary rusting and the galvanized steel surface shall have no grease, dust or water stains.
Subsequent Paint Super weather resistance flurorocarbon anticorrosive surface paint, flourcarbon anticorrosive surface paint and flourcarbon metallic flash paint.
Limitations Substrate temperature must be 3℃ higher than dew point above, and relative humidity must be less than 85%.
Safety Precautions This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.
This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done;
The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air.
Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary.
Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately.
Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation. Handle empty containers with care and do not bring about environmental contamination.
NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.