%{tishi_zhanwei}%

X06-1 Vinyl Phosphating Primer

X06-1 Vinyl Phosphating Primer (two components)

Intended Uses With coloring and ferrous metal surface rendering, it is featured by strong adhesive force, good mechanical strength and rapid dry. Welding with paint will not affect welding quality, and can be applied as shop primer. It can play a role in anti-rust and phosphorization to strengthen adhesive force between basic material and coating. It can be used as shop pre-coating, nonferrous metal rendering and ferrous metal anti-rust primer.
Product Description It is prepared by polyvinyl butyral resin, anti-rust and solvent phosphating solution. It is packed into Component A and Component B. (chalky yellow)
Product Information Volume Solids 12%
Dry Film Thickness 8 microns
Theoretical Coverage 45g/m2,20.00m2/L(calculated by 8μm dry film)
Pratical Coverage Allow appropriate loss
Application Details Mix Ratio A:B=4:1 (By weight)
Curing Time It can be used after two components are mixed
Method of Application  
Airless Spray Recommended-Tip range: 17-21mm; Total fluid pressure: 15-20MPa
Brush or Roller Recommended, only for small area.
Conventional Spray Adoptable but thin to 5-10%, Tip range: 2-2.5mm
Thinner X06-1 Special thinner
Cleaner X06-1 Special thinner
Pot Life 5℃-12h,25℃-8h,35℃-6h
Storage Life 6 months
Drying
Time
Substrate
Temperature
Touch
Dry
(h)
Hard
Dry
(h)
Full Solidification
(d)
Overcoating Interval
Minimum Maximum
25℃ 15 24 7 1 hours 24 hours
Storage and Handing Storage Store in cool and dry conditions
Pack Size Component A: 16kg, Component B: 4kg
Flash Point 15℃
Specific Gravity Approx 0.90kg/L
Specification and Surface Preparation Nonferrous metal shall be polished slightly to remove oil dirts, ferrous metal reaches sandblasting de-rusting Grade St2.
Subsequent Paint Various anti-rust paints.
Limitations Substrate temperature must be 3℃ higher than dew point above, and relative humidity must be less than 85%.
Safety Precautions This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.
This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done;
The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air.
Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary.
Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately.
Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.
Handle empty containers with care and do not bring about environmental contamination.
NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.