H06-1-3 Epoxy Zinc-rich Primer

H06-1-3 Epoxy Zinc-rich Primer(three components)

Intended Uses It is applicable to marine engineering, gas tank and steel structure which require heavy corrosion protection as anti-rust primer. It can also be painted on epoxy zinc rich shop primer.
Product Description Paint is prepared by epoxy resin, superfine zinc powder, polyamide resin, solvent and additives, etc. a large of zinc powders are contained in film with perfect cathodic protection effect is packed into Component A, Component B and Component C. A large of zinc powders are contained in film with perfect cathodic protection effect.(gray and semi-gloss)
Product Information Volume Solids 50%
Dry Film Thickness 80 microns
Theoretical Coverage 380g/m2,6.58m2/L(calculated by 80μm dry film)
Pratical Coverage Allow appropriate loss
Application Details Mix Ratio Component A (basic material): Component B: (zinc powder): Component C (curing agent)=21:70:9(weight radio)
Curing Time 23±2℃: 0.5~1h
Method of Application  
Airless Spray Recommended-Tip range: 17-21mm; Total fluid pressure: 15-20MPa
Brush or Roller Recommended, only for small area.
Conventional Spray Adoptable but thin to 5-10%, Tip range: 2-2.5mm
Thinner X-7
Cleaner X-7
Pot Life 5℃: 12h, 25℃: 8h, 35℃: 6h
Storage Life 一年
Full Solidification
Overcoating Interval
Minimum Maximum
25℃ 1 24 7 24h 7 days
Storage and Handing Storage Store in cool and dry conditions
Pack Size Component A: 15kg, Component B: 50kg, Component C: 6.4kg.
Flash Point Component A: 24℃, Component B: 27℃.
Specific Gravity Approx: 2.40kg/L
Specification and Surface Preparation The steel surface: Blast clean to Swedish Standard SIS055900 Sa2.5 or rust-removed manually or with power tool to St3. Should be clean and dry.
Subsequent Paint Epoxy resin paint, epoxy asphalt paint, chlorinated rubber paint, acrlic paint, polyurethane paint, chlorosulfonated polythylene paint and high chlorinated polyethlene paint, etc.
Limitations Substrate temperature must be 3℃ higher than dew point above, and relative humidity must be less than 85%, when construction substrate temperature is less than 5℃, epoxy and curing agent will stop reaction, and construction can not bu conducted.
Safety Precautions This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.
This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done;
The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air.
Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary.
Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately.
Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.
Handle empty containers with care and do not bring about environmental contamination.
NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.