H06-1-1 Epoxy Zinc-rich Primer

H06-1-1 Epoxy Zinc-rich Primer(two components)

Intended Uses	Because of its high content of zinc powder (> 77% by volume or 81% by weight in the dry film), it has fine cathodic protection to substrates. It possessed excellent adhesion, abrasion resistance, resistance to impact anticorrosion and durability. Able to match with most anticorrosive paints and top coats, used for anticorrosive primer of various steel structures in heavy duty anticorrosion. It is the best primer matched with epoxy intermediate coat or finish.
Product Description	High-performance, Two packages, Grey.
Product Information	Volume Solids			60%
	Dry Film Thickness			75 microns
	Theoretical Coverage			338g/m²
	Pratical Coverage			Allow appropriate loss
Application Details	Mix Ratio			A:B=10:1(by weight)
	Curing Time
	Airless Spray			Recommended-Tip range: 17-21mm; Total fluid pressure: 15-20MPa
	Brush or Roller			Recommended, only for small area.
	Conventional Spray			Adoptable but thin to 5-10%, Tip range: 2-2.5mm
	Thinner			X-7
	Cleaner			X-7
	Pot Life			5℃: 12h, 25℃: 8h, 35℃: 6h
	Storage Life			一年
	Drying Time	Substrate Temperature	Touch Dry （h）	Hard Dry （h）	Full Solidification （d）	Overcoating Interval
						Minimum	Maximum
		25℃	1	24	7	24h	No limit
Storage and Handing	Storage			Store in cool and dry conditions
	Pack Size			A: 30kg in 20 liter container B: 3kg in 4 liter container
	Flash Point			Above 24℃(mixture)
	Specific Gravity			Approx 2.7kg/L
Specification and Surface Preparation	The steel surface: Blast clean to Swedish Standard SIS055900 Sa2.5 or rust-removed manually or with power tool to St3. Should be clean and dry.
Limitations	This product can not fully cure below 5℃, so the substrate temperature should be above 10℃ for good effect. The surface to be coated with this product must be clean, dry and free from zinc salt before application.
Safety Precautions	This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product. This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done; The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air. Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary. Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation. Handle empty containers with care and do not bring about environmental contamination. NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.