%{tishi_zhanwei}%

IPN-8710 IPN Paint

IPN-8710 IPN Paint (primer/surface paint, two components)

Intended Uses Paint film has strong adhesive force, wear resistance, good softness, bright color, oil resistance, benzene solvent resistance, and waterproof, boiling water resistance, sea water resistance, wet hot resistance, acid resistance, alkali resistance, slat resistance and chemical corrosion resistance, it is a kind of mew anticorrosive decorative paint with good weather resistance. It is applicable to anti-corrosion and decoration of indoor and outdoor steel structure and concrete facility surfaces like petrochemical engineering, metallurgy, electric power, gas chamber, traffic and mechanical equipment, etc.
Product Description   This paint is two-component paint, Component A is prepared by polyester polyurethane resin and initiator color filler, Component B is prepared by activated monomer as styrene and acrylonitrile, etc. After two components mix, polyurethane acrylate polymer with synergistic effect blends interpenetrating network. (Primer: rust, surface paint: various colors)(Other colors can be provided according to requirements)
Product Information Volume Solids 47%
Dry Film Thickness 35 microns
Theoretical Coverage Primer: 130g/m2, Surface paint 115g/m2(calculated by 35μm dry film)
Application Details Mix Ratio Primer: A:B=4:1 (weight ratio)/Surface paint: A:B=5:1(weight ratio)
Curing Time 23±2℃:3min
Method of Application  
Airless Spray Recommended-Tip range 0.33-0.41mm, Output fluid pressure; 17.6-21.1MPa(176-211Kg/sq.cm)
Brush or Roller Recommended, only for small area.
Conventional Spray Adoptable but thin to 5-10%, Tip range:2-2.5mm
Thinner IPN-8710 Speical diluent
Pot Life 25℃:8h
Storage Life 6 months
Drying
Time
Substrate
Temperature
Touch
Dry
(h)
Hard
Dry
(h)
Full Solidification
(d)
Overcoating Interval
Minimum Maximum
0℃
25℃
35℃

2
1

24
18
7 3h
2h
1h
48h
24h
16h
Painting number Primer is painted two coats, dry film reaches 70μm, and then surface paint is painted 2-3 coats, dry film reaches 70~100μm.
Storage and Handing Pack Size Primer: Component A 18kg, Component B 4.5kg; Surface paint: Component A 20kg, Component B 4kg。
Flash Point Component A 25℃, Component B 30℃。
Specific Gravity Primer: approx 1.53kg/L, Surface paint approx 1.27kg/L。
Specification and Surface Preparation Steel surface requires sand blasting or shot blasting to Swedish Derusting Standard Sa2.5, or grinded to St3 by electric tool, roughness formed on steel surfaces shall be controlled within 40~80μm. Steel surface shall be painted primer within 24h after removing rust to avoid second rust.
Limitations Two-component paint shall be stired adequately, conducted match according to required quality, and constructed after 20min stationary.
Safety Precautions This product should be used in painting area by professional operations. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.
This product is a kind of solvent-based paint. In order to avoid danger or accident, minimal safety precautions, as follow, should be done;
The paint contains volatile solvent and is flammable. So must keep away form sparks and open flames. No smoking at application site. Effective precautions (such as using explosion-proof electrical equipments, no static electricity accumulation or metal collision etc) also should be done so as to avoid producing sparks. Flash point of paint, mentioned above o Product Data Sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air.
Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general. Therefore, 200m3 of ventilation quantity per 1kg solvent (according to the solvent) is necessary.
Protect skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks, barries creams and so on). If paint gets in touch with skin, wash fully with a large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately.
Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation. Handle empty containers with care and do not bring about environmental contamination.
NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), out company will NOT be responsiblefor any accident.